xxcdcxxsetxx
Terms
undefined, object
copy deck
- What is a requirement for military explosives?
- Raw materials must be cheap.
- Volatility is the tendency of a substance to produce?
- Vapors
- The rate of transformation for high explosives is between?
- 3,200 and 28,000 feet per second
- The tendency of a substance to burn with a rapid and sparkling combustion is called?
- Deflagration
- What are the detonation products?
- Heat, Light, Gases, and pressure.
- How do we classify explosive train primers?
- By the way they are initiated.
- How can you increase the penetration effect of a shaped charge?
- Increase standoff distance.
- For what purpose do we use a shaped charge?
- To produce an explosive penetration of a solid object.
- The four factors that control the visibility of pyrotechnics are?
- Candlepower, color, weather, and light.
- Name two types of effects for signals?
- Light and Smoke.
- What pyrotechnic effect is produced by the AN-MK13 Signal?
- Smoke and Flare.
- How is the A/P25S-5A distress signal kit ignited?
- Percussion Primer.
- How much light does the M127A1 signal produce?
- 50,000 candlepower.
- What effects do the booby-trap simulators provide?
- Flash, Illumination, and a Whistling Sound.
- What is the largest caliber ammunition that we classify as "small arms"?
- Caliber .50
- What shotgun round is the exception to the gauging principle?
- 410
- What hazard is involved in using blank ammunition?
- The wad can cause injury.
- What are the components of a typical small-arms cartridge?
- Cartridge case,primer,bullet, and propellant.
- Name three classifications of Air Force grenades?
- Service, Practice, and Training.
- What type of explosive filler does an M26 fragmentation grenade have?
- Composition B.
- What substance is the explosive filler for the M30 practice grenade?
- Black Powder
- Which chemical filler is used in the AN-M8 smoke grenade?
- Hexachloroethane
- Which mine do we commonly call the "claymore"?
- M18A1
- How far in front of an M18A1 mine do we consider inside the danger zone?
- 250 meters
- How much force is required to function the M14 anti-personnel mine?
- 20 to 35 pounds.
- What mortar can be broken down into several smaller loads for easier carrying?
- Medium
- What color is the most common for military safety fuze?
- Green.
- What device is used to intiate time fuse?
- M60 Igniter.
- What substance is the M112 demo block made of?
- Compostion C-4
- The main types of fuze actions are?
- Impact, Time, and proximity.
- Where is a proximity fuze placed on the bomb?
- Nose
- In an electronically timed fuze, what component replaces the arming vanes used in mechanically timed fuzes?
- Electric charging assembly
- The design of which safety feature is to prevent movement of the arming heads, arming stems, and strikers while the fuze is being handled?
- Cotter pins
- What adapter booster is used with the M904 fuze?
- T45
- Where in a bomb body is the M905 fuze installed?
- The tail fuze well.
- The FMU-54 series tail fuzes are used in?
- MK80-series general-purpose bombs with an air inlatable retarder.
- With electrical fuzes, what device is used in place of arming wire?
- Battery-firing device.
- How can you tell when an FMU-124A/B fuze is armed?
- The safety pin is removed and the release shaft is extended
- What setting causes the FMU-139A/B fuze to abort and not arm?
- "Low-Drag Arm Time" knob set to the "X" position.
- What component provides the electrical power needed to operate the FMU-139A/B fuze?
- FZU-48/B initiator
- What provides the electrical power needed to operate the FMU-143 series fuze?
- FZU-32 series fuze initiator
- Where are proximity sensors/fuzes installed on a bomb?
- Nose
- Which sensor is a radio-frequency radar ranging system used with the suspension utility unit (SUU)64/B,65/B,66/B dispensers?
- FZU-39/B
- What does HOF stand for on the FZU-39/B proximity sensor?
- Height of function
- Which proximity fuze has a height-of-burst (HOB) setting built into the fuze at the time of manufacture?
- FMU-113/B
- What component is used to adapt a nose fuze for an M-series bomb?
- Adapter booster
- Which fin provides a high-drag, low altitude bombinb capability for the M117 bomb?
- BSU-93/B
- What air inflatable retarder (AIR) is used on the MK84 bomb?
- BSU-50/B
- Which bomb is not classified as a penetrator?
- BLU-126
- What type of bomb is the BLU-113?
- 4,000 pound penetrator bomb
- What bomb is filled with a thermobaric explosive?
- BLU-118
- What bomb is used as the warhead in the GBU-28C/B?
- BLU-122
- What is the M129 Bomb used for?
- Deliver propaganda leaflets used to persuade the enemy to surrender.
- What suspension utility unit (SUU) does the PDU-5/B utilize?
- SUU-76C/B
- The BLU-126/B is identical to the?
- MK82, 500 pound bomb.
- What is the net explosive weight (NEW) of the BLU-126/B?
- 27 pounds
- What is the weight of the BDU-33 series practice bomb?
- 25 pounds
- What is the weight of the BDU-48 series practice bomb?
- 10 pounds
- The BDU-48/B resembles the ballistics of the?
- MK82 high drag munitions
- Which submunitions are loaded into a CBU-87 cluster bomb?
- BLU-97 bomblets
- The major physical difference between the CBU-87/B and the CBU-89/B cluster bombs is the?
- CBU-89/B does not have canted fins
- How many different types of bomblets are loaded into a single CBU-89/B cluster bomb at one time?
- Two
- Which suspension utility unit (SUU) dispenser does the CBU-97 cluster bomb use?
- SUU-66
- Against what types of targerts is the CBU-97/B primarily used?
- Tanks
- How do we classify 20 millimeter (mm) ammuntion?
- Projectile
- How do we CLASSIFY 20 (MM) Ammo?
- According to its purpose
- Which part of the target practice 20 millimeter (MM) round is inert?
- Projectile
- What is one significant difference in 20 (mm) ammuntion compared to other cannon ammunition?
- The electrically fired primer.
- What M505-series fuze safety feature prevents accidental arming during handling?
- Fuze is bore safe.
- The identifying information on a 20 (MM) round of ammunition is marked on the?
- Projectile.
- What will not cause the electrical primer in 20 (MM) ammunition to be fired accidentally?
- Proper handling.
- What aircraft cannon fires the 25 (MM) round?
- GAU-12
- When 25 (MM) ammunition is bulk-packed, how many rounds do you expect to find in a CNU-405 container?
- 80 or 100
- What device holds the ball rotor of the 30 (MM) M505A3 impact fuze in an unarmed position until it is fired?
- Lock ring
- What is the purpose of the 30(MM) dummy ammuntion?
- Familiarization training and mechanical cycling of the gun system.
- What material is the 30 (MM) cartridge case made of?
- Aluminum
- What fuze is used in 30(MM) high explosive incendiary ammuntion?
- M505A3
- How many lot numbers can you expect to find on a 30 (MM) round of ammunition?
- Three
- Name the components of a 40 (MM) round?
- Primer,Cartridge Case,Propellant charge,Projectile, and Fuze
- What is the total number of rounds the MK1 ammunition box hold?
- 16
- What do we mean when we say the 105 (MM) is "fixed" ammunition?
- The propellant charge is not adjustable.
- What type of explosive is loaded in the projectile of the 105 (MM) high explosive round?
- Comp B.
- Approximately how many fragments will the high fragmentation PGU-45/B projectile produce?
- 13,000
- What is the factory set height of burst (HOB) for the FMU-160/B fuze to optimize lethality?
- 15-foot
- What are the components of the 105 (MM) round?
- Cartridge case, propellant charge, primer, projectile, and fuze.
- What major aircraft sytems carry countermeasure flares?
- All major tactical, bomber, and cargo aircraft.
- Which impulse cartridge intiates the MJU-7/B flare?
- BBU-36/B
- What does the SD-206 infrared flare do?
- Provides smoke to simulate a flare for training purposes.
- Which component is part of the ALE-50 series towed decoy system?
- Launch controller.
- Which impulse cartridge does the RR-170 chaff cartridge use?
- BBU-35/B
- The LUU-2 series aircraft flare procedures?
- Two million candlepower for an average burn time of five minutes.
- What output does the LUU-5/B target marker produce?
- Green light.
- What impulse cartridge supplies the gas pressure to launch the flares from the SUU-25E/A dispenser?
- ARD 863-1
- The gas pressure produced by the impulse in an SUU-25 ejects the flare at a speed of approximately?
- 65 feet per second.
- What are intiators designed to do?
- Supply gas pressure to operate other cartridge-activated devices.
- What are catapults used for?
- Ejecting a seat and crew member safely from an aircraft.
- What are removers designed to do?
- Eject aircraft canopy.
- What are the two types of impulse cartridges?
- Explosive and Non-explosive.
- When using a drill, the first thing you do is?
- Make sure the diameter of the hole to be drilled is within the capacity of the drill.
- Which diameter (in inches) electric saw blade is the most common found in maintenance activities?
- 8"
- An electric saw's blade must be operating at what speed before it contacts the material being cut?
- Full.
- How many pounds per square inch (psi) of clean, dry air are required at the tool end of the air hose to ensure safe and efficient operation of the tool?
- 90.
- Which pneumatic impact tool is designed for installing or removing nuts and bolts?
- Wrench.
- At what variation in pounds of pressure, while using an impact wrench, can the excess pressure become serious?
- 5.
- What is the most common type of sling used in your everyday job?
- Wire Rope.
- Hoist hooks must be replaced when they have more than?
- 15% in excess of normal throat opening or more than 10% twist from the plane.
- The common practice that applies to any meter is always?
- verify that power is off when connecting the meter.
- Which meter is a four-wire Kelvin digital ohmmeter used for testing AIM-9 and the AIM-120 missile system?
- AMTEC 620
- Which tester is a stable precision instrument designed primarily for the testing of solid-fuel rocket motor igniter bridge wire circuitry?
- 101-5BFG
- The maximum load capacity of the MHU-141/M trailer is?
- 5,500 pounds.
- The steering system on the MHU-141/M trailer has a turning radius of?
- 200 inches
- When the MHU-141 trailer is loaded or towed with the hinged deck open, what must be done?
- The two deck-panel supports must be properly positioned and locked in place with quick-release pins.
- The parking brake on the MHU-110/M trailer affects how many wheels?
- Four inboard rear wheels.
- What is the maximum capacity of a pair of rail extender assemblies used with the MHU-110/M?
- 3,000 pounds.
- How many trolley and chock assemblies are supplied with the MHU-110/M?
- 20 Trolleys and 40 Chocks.
- What is the maximum load capacity of the MHU-226 trailer?
- 12,000 pounds.
- How many openings are on the deck of the MHU-226 trailer?
- 3
- What ensures the smooth transfer of HCU-6/E pallets from a rollerized trailer to an aircraft/K-loader?
- An adjustable ramp.
- The moving of munitions and weapons from one base to another, depot to base, or base to depot is called?
- A logistical movement.
- Movement to support on-base operations to or from the flight line is called?
- An operational movement.
- Which lift truck has a manually extendible wheelbase?
- MHU-83 series bomb-lift truck.
- Which lift truck has cantilever lift arms?
- MJ-1 series aerial stores lift truck.
- The purpose of the transport beam beneath the lift arm assemblies on the MJ-1 series lift truck is to?
- Provide added support and to relieve excess hydraulic pressure from the lift arms in carrying loads for long distances.
- What is the lifting capacity of the MJ-1?
- 3,000
- When using MJ-1 lift truck extension lift arms, you immediately?
- reduce its lifting capacity by 800 pounds.
- What is the lifting capacity of the MHU-83 series lift truck?
- 7,000 pounds.
- When using the MHU-83B with fork adapters, you immediatly?
- Reduce its lifting capacity by 1,000 pounds.
- When releasing the accelerator pedal on a vehicle driven with a hydrostatic transmission, the?
- Unit coasts to a stop very quickly.
- What is the drawback to using the hydraulic hand pump to build hydraulic pressure on the MHU-83 B/E?
- Extremely slow way to build hydraulic pressure.
- What are the minimum and maximum frame-width adjustments of the MHU-83 B/E?
- 70 inches; 140 inches.
- How do you adjust the yaw on the MHU-83 B/E?
- Hydraulically.
- What is the rated capacity of air per minute needed for the MC-7 air compressor to discharge 100 PSI of pressure?
- 125 cubic feet.
- The MC-7 air compressor is designed for?
- General Maintenance
- The diesel model of the MC-7 air compressor is capable of operating up to how many hours at a time without refueling?
- 8
- What is the primary difference between a bobtail and a pickup?
- The bobtail's back end is shortened by about one-half.
- The unique and handy feature of the bobtail truck's center pintle hook is that it can be unpinned and?
- Moved in, out, or sideways for ease of trailer hookup.
- The maximum towing speed of the bobtail while towing equipment is?
- 15 mph.
- Which AF form is used to document a daily inspection on a general cargo truck?
- 1800
- What is the purpose behind good operator maintenance of all assigned vehicles?
- Maintain vehicle serviceability at reduced cost.
- What is the maximum tow capacity of the MB-4 aircraft towing tractor?
- 140,000 pounds.
- Which position should the differential shift lever be in while driving the MB-4 towing tractor on dry road surfaces?
- Unlocked.
- What range should be selected in a tractor with an automatic transmission while going down grades?
- Low range
- Which procedure is not a consideration for backing a tractor/trailer combination?
- Turn toward the passengers side.
- What is the maximum depth of water you may drive a rough-terrain forklift through?
- 5 feet.
- Which forklift has the solid front axle and a pivot pin that allows the front end to pivot when turning the steering wheel, making it very dangerous when climbing in or out?
- Adverse-terrain forklift.
- What is the maximum reach of the variable-reach forklift with the forks elevated at 45 degrees?
- 15 feet.
- Which type of forklift has a "dead-man" switch that can be operated from the driving position?
- Electric.
- When can you store powered equipment in a building with explosives?
- Only when stored in fire-resistive buildings and such equipment is essential to day to day operations.
- Which ammuntion loading system services the M61A gun system?
- Linkless ammuntion loading system (LALS)
- Which component is not one of the five weapons replaceable assemblies?
- Ammunition drum.
- Which T.O. covers the linkless ammunition loading system? (LALS)
- 35D2-19-1
- Which weapons replaceable assembly receives ammuntion from three bays of the container assembly and merges them into a single stream?
- Transfer unit.
- Which weapons replaceable assembly consists of the flex drive assembly?
- Conveyor.
- Which component transfers rounds into the aircraft gun feed system?
- Universal aircraft interface unit.
- What is the maximum number of rounds the (UALS) drum can hold?
- 2,100
- Use the cable-type load binder to secure?
- Unbolstered weapons on the MHU-141/M trailer
- How do you extend the CGU-1/B strap?
- Release the adjusting mechanism;pull the strap.
- Many nuclear weapon bolsters are designed with an attachment point for a tow bar,but one exception is the?
- H1125
- How often are courriers certified?
- Anuually
- What code word is used when a Department of Energy (DOE) convoy seeks sanctuary during and emeergency?
- Safe Haven
- What IMT is use to transfer custody of missile warheads?
- AF IMT 514
- Which component of the munitions assembly conveyor (MAC) is dissasembled last?
- Gantry