Aviation Support Equiment Questions
Terms
undefined, object
copy deck
- On _____, BUPERSNOTE 1440 announced that a new rating (AS) was being established.
- February 24, 1966
- This NEC requires on-equipment repairs and intermediate level maintenance on mobile air-conditioners(C-17 & 21).
- AS-7603
- OPNAV 4790/52
- SE PreOperational Record
- OPNAV 4790/51
- SE Equipment History Card
- OPNAV 4790/64
- Transaction Report
- OPNAV 4790/102
- Support Equipment License
- Maintenance Data Report 10
- FOD
- To acquire this NEC, you must plan, organize, implement, and control maintenance on all assigned SE in compliance with policy and NAVAIR directives.
- AS-7609 SE Maintenance Manager
-
What is the primary causes of premature engine failures in support equipment?
A. Improper maintenance actions
B. Water in the oil
C. lack of trained personnel
D. Dirt and water in fuel - D. Dirt and water in fuel
- What is the primary manual you should use in the prevention, detection, and repair of corrosion on support equipment?
- NAVAIR 17-1-125
- Naval Aviation Maintenance Program (NAMP) is also called?
- COMNAVAIRFOR 4790.2
- Who retains the pink copy of the Support Equipment Transaction Report?
- The activity using the equipment
- The A/M27T-5 portable hydraulic power supply is rated at ___ gpm(gallons per minute)at ___ psi
- 20 gallons per minute at 5000 psi.
- The ______ tow tractor is more commonly referred to as a "spotting dolly."
- A/S32A-32
- What type refrigerant is used to service the C-17 and C-21?
- R-22
- _____ heat is the number of Btu that must be added to a unit weight of substance to raise its temperature 1 degree Fahrenheit.
- Specific Heat
- What are the three laws that govern heat transfer?
-
1. Heat always flows from a hot object to a cooler one.
2. The greater the difference in temperature, the faster the heat flows.
3. Heat will continue to flow until all temperatures equalize. - The transfer of heat can be accomplished in one of three ways?
- Radiation, Convection, Conduction
- The six major components of an air-conditioning system are?
- Compressor, Condenser, Receiver, Heat exchanger, Metering device(expansion valve), and evaporator
- Which state is the refrigerant in as it enter the compressor and exit the condenser?
- Enters as a low pressure Vapor and exit as a High pressure liquid.
- Where does the refrigeration cycle began?
- Low pressure side of the compressor and the high pressure side of the expansion valve.
- Which of the following components will entrap the liquid refrigerant during the pump down cycle of the C-17?
- The receiver
- ______ results from a direct chemical attack on the exterior and only involve metal surfaces.
- Uniform Surface Corrosion
- _______ occurs when different metals are in contact with each other and an electrolyte(such at salt water).
- Galvanic Corrosion
- _______ is an advanced form of intergranular corrosion and occurs when the surface grains of a metal are lifted at the grain boundaries.
- Exfoliation Corrosion
- The most common corrosion on aluminum and magnesium alloys is called
- Pitting Corrosion
- _______ is the cracking of metals caused by the combined effects of cyclic stress and corrosion and is very similar to stress corrosion cracking.
- Corrosion Fatigue
- Corrosion appearance on Magnesium Alloy?
- White, powdery, snow-like mounds and white spots on surface
- Corrosion appearance on low Alloy Steel?
- Reddish-brown oxide(rust)
- Corrosion appearance on Aluminum Alloy?
- White to gray powder
- Corrosion appearance on Stainless Steels(300-400 series)?
- Rough surface; sometimes a red, brown or black uniform stain
- Corrosion appearance on Alloy, Brass, Bronze?
- Blue or blue-green powdery despoit
- What form is used to designate QAR's and CDI's
- OPNAV 4790/12
- What is a 4790/60?
- VIDS MAF
- Support Equipment Misuse and Abuse are document on what form?
- OPNAV 4790/108
- OF346(11-85)?
- US Government Motor Vehicle Operators License
- What report tracks monthly maintenance production?
- MDR-2
- What report is used to monitor technical directive that have not been complied with?
- MDR4-1
- Corrosion control is what Maintenance Data Report?
- MDR-11
- The MO shall designate in writing via the MMP, the __ as the Maintenance Training Program Manager?
- AMO
- The _____ manage the S/E training and license program for I-level?
- Support Equipment Division Officer
- Indoc training shall be provided to all newly assigned personnel with __ days of reporting, but may be extended to __ days if operational commitment exist.
- 30 and 60
-
Hydraulic pumps are normally rated in terms of volumetric output and
A. Temperature
B. Flow rate
C. Pressure
D. Size - C. Pressure
-
What type of pump is used on the B-2 maintenance platform?
A. Single-action hand pump
B. Variable-displacement pump
C. Double-action pump
D. Rotary pump - C. Double-action pump
-
What is the primary function of a hydraulic filter?
A. The retention of insoluble contaminants from the hydraulic fluid
B. The retention of soluble contaminants from the hydraulic fluid
C. To remove chlorinated solvent from the hydra - A. The retention of insoluble contaminants from the hydraulic fluid
-
All aircraft hydraulic servicing units must be equipped with a final filter of what micron rating?
A. 3 micron
B. 10 micron
C. 5 micron
D. 15 micron - A. 3 micron
- The TMU-70/M is a completely self contained unit. It has three major components, what are they
- 50 gallon dewar tank, a 15 liter transfer tank, and a low-loss closed loop(LLCL) system of transfer lines
-
Which of the following components keep the front wheels in proper alignment?
A. The pitman arm
B. The tie rod
C. The drag link
D. The connecting rod - B. The tie rod
- Which of the following statements best describes wheel caster?
- The number of degrees the steering knuckle is tilted to the rear or front
-
Front-end geometry does NOT include which of the following terms?
A. Caster
B. Camber
C. Pinion tilt
D. Pivot inclination - C. Pinion tilt
-
What are the principal parts of a steering gear unit?
A. The worm gear and sector
B. The worm gear and connecting rod
C. The sector and pitman arm
D. The sector and recirculating balls - A. The worm gear and sector
- To correct toe-in of a vehicle, you must adjust what components(s)?
- The steering arm knuckle
-
Which of the following sections of a turbine is designed to increase the pressure of the air and discharge it to the combustion chamber?
A. The turbine section
B. The accessory section
C. The cumbustion section
D. The compressor - D. The compressor section
- Which of the following section of a gas turbine engine contains the starter, oil pump, centrifugal switch, the fuel pump, and the generator?
- The accessory section
-
What type of fuel atomizer is used on the gas turbine engines found in support equipment?
A. A full flow
B. A dual orifice
C. A variable output
D. A adjustable nozzle - B. Dual orifice
-
Which of the following components is installed on the gas turbine engine to prevent accumulation of unburned fuel in the turbine plenum?
A. A drain check valve
B. Overflow valve
C. A pressure valve
D. A discharge vavle - A. A drain check valve
-
Which of the following is NOT a switch located in the centrifugal switch?
A. 10% switch
B. 35% switch
C. 95% switch
D. 110% switch - A. 10% switch
- What are the six(6) programs managed by Quality Assurance?
- NAMDRP, CTPL, SE Misuse and Abuse, AVGFE, Maintenance Safety, QA auditing
- What are the three main sections of the GTC-85 and the A/M27A-4 composed of?
- Compressor, Turbine, Accessory
- The MO shall designate in writing via the MMP the ____ as the Tool Control Program manager.
- Material Control Officer
- For shore AIMD's the responibility of the Tool Control Program Manager may be delegated to the ____ or ____
- AOIC or MMCO
- What is the duty starting cycle for gas turbine engines?
- 1 minute on, 4 minutes off
-
Which of the following components keep the front wheels in proper alignment?
1.The pitman arm
2.The tie rod
3.The king pin
4.The connecting rod - 2.The tie rod
-
The pitman arm connects the steering gearbox to which of the following components?
1. The tie rod ends
2. The king pins
3. The axle
4. The connecting rod - 4. The connecting rod
-
What are the principal parts of a steering gear unit?
1. The worm gear and sector
2. The worm gear and connecting rod
3. The sector and pitman arm
4. The sector and the Recirculating balls - 1. The worm gear and sector
-
Which of the following conditions can cause excessive play in the steering system?
1. Improper adjustment of the steering gear unit
2. Improper adjustment of the steering linkage
3. Improper adjustment of the brakes
4. Improper wheel alignmen - 2. Improper adjustment of the steering linkage
-
Front-end geometry does NOT include which of the following terms?
1. Caster
2. Camber
3. Pinion tilt
4. Pivot inclination - 3. Pinion tilt
-
Which of the following statements best describes wheel caster?
1. The number of turns required to adjust the connecting rod one inch
2. The number of inches the front wheel points in towards the center of the unit
3. The number of degrees the whe - 4. The number of degrees the steering knuckle is tilted to the rear or front
- Why is support equipment painted white?
- As a verification that the equipment was painted with lead-free paint.